2014년 1월 6일 월요일

About 'electric motor bearing replacement'-How to Change Bearings on a Indesit Washing Machine







Go to last comment about ' electric motor bearing replacement?' Voted up & Useful... Thank you for this post and I agree integrating them... Great! Thank you very much! I will post the link to the translation here... Interesting and well-written Article... Thank you for sharing...



About 'electric motor bearing replacement'-How to Change Bearings on a Indesit Washing Machine








The               evaporative               cooler               (swamp               cooler)               can               be               a               great               asset               to               a               homeowner,               if               used               correctly.

As               a               residential               handyman,               I               see               many               improper               setups.

I               also               see               many               people               sweltering               in               the               heat               when               a               swamp               cooler               would               easily               take               care               of               their               cooling               needs.

The               first               of               the               big               four               mistakes               is               a               general               misunderstanding               of               what               an               evaporative               cooler               is,               and               what               it               isn't.

It               is               not               just               a               cheap               version               of               an               air               conditioner.

They               work               in               very               different               ways.

Swamp               coolers               also               work               best               in               dry               climates               such               as               New               Mexico,               Colorado,               or               Nevada.

You               must               also               understand               that               these               coolers               work               on               the               principle               of               air               displacement.

For               the               best               operation               you               must               open               windows               at               the               far               end               of               your               home               from               where               the               cooler               is               mounted.

Too               little               free               air               flow               will               make               it               overly               humid               and               stuffy,               as               well               as               decreasing               your               cooling               potential.

If               you               are               one               of               the               millions               who               bought               the               stand               alone               evaporative               units               from               a               home               improvement               store               in               the               past               few               years,               you               will               be               more               satisfied               with               your               purchase               if               you               set               it               in               front               an               open               window               (as               close               as               possible)               and               open               another               window               in               another               part               of               your               home.

If               you               are               drawing               the               air               in,               it               needs               to               go               out               somewhere.
               The               second               problem               is               improper               maintenance               of               the               evaporative               pad(s).

If               you               are               in               a               harsh               water               climate,               then               consider               supplying               your               cooler               water               from               a               filtered               source.

These               pads               clog               after               a               time               in               any               water               condition,               and               replacing               them               when               needed               will               greatly               enhance               the               efficiency               of               your               cooler.

An               old               pad               can               also               lose               some               of               it's               microbial               resistance,               thereby               allowing               small               amounts               of               mold               or               mildew               to               grow.

Anyone               having               seasonal               allergies               may               be               bothered.

Also               be               sure               to               buy               proper               fitting               pads.

A               four               inch               gap               at               the               top               of               an               intake               panel               will               cut               your               cooling               output               by               a               large               measure.

The               air               follows               the               path               of               least               resistance               (in               this               case,               around               the               pad)               and               lowers               your               efficiency               rating.
               The               third               trouble               area               is               improper               belt               tensioning               and/or               replacement.

Drive               belts               will               eventually               crack               and               glaze               over.

Proper               belt               tension               guidelines               are               usually               stamped               on               a               decal               on               the               blower               housing               or               framework.

Do               not               tighten               a               belt               more               than               recommended.

Doing               so               will               cause               excessive               wear               on               the               blower               bearings               and               make               the               whole               unit               noisier.

Don't               forget               to               add               a               few               drops               of               oil               in               each               blower               bearing               at               the               beginning               of               the               season.

Depending               on               your               make               and               model,               you               may               or               may               not               have               a               place               to               oil               the               electric               motor               bearings.

(Caution!

Over               oiling               creates               a               nasty               mess               to               clean               out               of               the               water               reservoir.)
               The               fourth               problem               can               usually               be               overcome               with               a               little               ingenuity               and               some               duct               tape.

This               applies               mostly               to               window               mounted               swamp               coolers.

I've               seen               many               coolers               mounted               and               operating               with               gaps               of               several               inches               between               the               housing               and               the               window               frame.

There               is               no               sense               in               cooling               the               air,               only               to               have               ten               percent               of               it               pumped               right               back               outside.

Take               time               to               fit               some               panels               around               the               part               of               your               cooler               that               sticks               into               the               room.

In               a               pinch,               use               some               heavy               duty               trash               bags               and               duct               tape               (or               any               other               heavy               duty               tape               of               your               choice)               to               seal               the               gap.

Whatever               you               do,               make               it               water               tight               enough               to               shed               rain,               or               an               errant               sprinkler.

After               all,               you               don't               want               to               be               replacing               a               window               sill               this               fall,               do               you?
               When               the               hot               season               is               over               be               sure               to               drain               the               supply               line               to               your               cooler               and               empty               the               reservoir               pan.

Cover               your               cooler               through               the               winter,               but               be               careful               when               setting               up               for               the               next               season.

A               mildly               warm               and               protected               cooler               in               the               early               spring               is               a               favorite               nesting               place               for               yellow               jackets               and               wasps.
               Enjoy               the               days               of               summer               .

.

.

and               keep               your               cool.






Image of electric motor bearing replacement






electric motor bearing replacement
electric motor bearing replacement


electric motor bearing replacement Image 1


electric motor bearing replacement
electric motor bearing replacement


electric motor bearing replacement Image 2


electric motor bearing replacement
electric motor bearing replacement


electric motor bearing replacement Image 3


electric motor bearing replacement
electric motor bearing replacement


electric motor bearing replacement Image 4


electric motor bearing replacement
electric motor bearing replacement


electric motor bearing replacement Image 5


  • Related blog with electric motor bearing replacement








  • Related Video with electric motor bearing replacement







    electric motor bearing replacement Video 1








    electric motor bearing replacement Video 2








    electric motor bearing replacement Video 3




    electric motor bearing replacement































    0 개의 댓글:

    댓글 쓰기